News:

Due to a technical issue, some recently uploaded pictures have been lost. We are investigating why this happened but the issue has been resolved so that future uploads should be safe.  You can also Modify your post (MORE...) and re-upload the pictures in your post.

Main Menu

Door handles loose on 38 caddy

Started by Bob Martin, June 11, 2017, 04:47:32 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Bob Martin

Is there a procedure to tight the outside door handles on my 1938 60S?
Thanks, Bob
Bob Martin
CLC # 28309
1938 60S, #6273078

tripwire

Bob,
By loose do you mean the handle wobbles up and down?  Are there any rubber grommets in place between the door and the handles?  If not, get some and put them in.  Repros are available from CaddyDaddy and Steele Rubber.
If you mean loose by the handles moving in and out of the door then the screws that hold the handles to the door latch are loose or missing.  Those are an odd tapered screw that goes into a hole in the lock mechanism.  You should be able to see them through a hole in the door near where the latch is.
Also, have a look at this posting:  http://forums.cadillaclasalleclub.org/index.php?topic=144440.msg357794#msg357794

WParo in VT
 
Driving now:
2013 CTS4 Performance Coupe
1940 LaSalle 5229 C4D

A few I used to drive:
1976 Cadillac Ambulance
1969 Cadillac Hearse, Superior Body
1966 Buick Wildcat Hearse
1957 Ford Thunderbird x 3, 1 E code, 2 D code
1956 Oldsmobile Rocket 88 Sedan
1949 Mercury Convertible
1949 Mercury Coupe, Mild Custom
1936 Buick Special Sedan

Bob Martin

It might just be the rubber bushing. I'll look today when I go to my garage.Easy fix if so.
If I loosen the screw inside the door mechanism, will I be able to just remove the handle?
Seem's I looked at this once before, but was afraid to lose the screw in the door panel.
Will follow up.
Thanks,
Bob
Bob Martin
CLC # 28309
1938 60S, #6273078

tripwire

Bob, the screw has to come all the way out.  Be careful or you'll lose it. Also, the receiving end tends to strip or be stripped quite easily.  Put some PB Blaster on it and let it set for a week or so before you get all gorilla on it.
Driving now:
2013 CTS4 Performance Coupe
1940 LaSalle 5229 C4D

A few I used to drive:
1976 Cadillac Ambulance
1969 Cadillac Hearse, Superior Body
1966 Buick Wildcat Hearse
1957 Ford Thunderbird x 3, 1 E code, 2 D code
1956 Oldsmobile Rocket 88 Sedan
1949 Mercury Convertible
1949 Mercury Coupe, Mild Custom
1936 Buick Special Sedan

Steve Passmore

Bob, You cannot screw the screw all the way out and loose it because it would foul the inside surface if the door before being fully out(its about 1.5" long). You have to hold the handle slightly down to line up the screw head with the hole and keep on unscrewing. If the threads are all good it will not be fully unscrewed until the head is partly out of the hole. Then you might loose it on the floor ;D
Steve

Present
1937 60 convertible coupe
1941 62 convertible coupe
1941 62 coupe

Previous
1936 70 Sport coupe
1937 85 series V12 sedan
1938 60 coupe
1938 50 coupe
1939 60S
1940 62 coupe
1941 62 convertible coupe x2
1941 61 coupe
1941 61 sedan x2
1941 62 sedan x2
1947 62 sedan
1959 62 coupe

Paul Phillips

Bob
There are several potential causes for what I think you are describing.  It may be helpful to understand what you are experiencing. 

The tapered screw secures the handle shaft into the lock mechanism. If that screw is loose, the handle would have rotational free play. Also, if it is loose on all doors, that would be quite unusual, unless all affected doors had been taken apart recently. Usual problem with the tapered screw is it is frozen in place, making solving other problems difficult.

The rubber bushing is part of a ferrule that is crimped to the door skin. Also a bit unusual to affect all doors at same time. This failure is less of a rotational free play, and more where the handle is floppy about the axis of the handle shaft, no matter what the orientation.

The other item to check are the springs in the lock mechanism. These are also known failure items, frequently found broken after this many years.  Another symptom of this problem is the handle is 'droopy', instead of sitting horizontal in the nominal position. Correcting this requires removing the tapered spring to remove the handle, then removing the lock assembly from the door to service the internal springs. You will need to remove the door panel & all of the other linkages - inside lock slide, key lock, and the relay link for the inside door handle. A service manual is helpful to see an image of all the bits. These springs are typical for GM cars of the vintage, and should have several sources.

Good luck with your repair!

Paul
Paul Phillips CLC#27214
1941 60 Special (6019S)
1949 60 Special (6069X)
1937 Packard Super 8 Convertible Victoria
1910 Oakland Model 24 Runabout